Skip to content
Sourcing Allies
Cooling Systems
Founded in Sweden in 2006 · Over 1 million products shipped from Asia · Offices in Bellevue WA, Djursholm and Ningbo

Cooling system manufacturer in China and Vietnam. One partner answers for the whole unit.

For HVAC, refrigeration, cold-chain and food-service equipment companies building or scaling a complete cooling unit. We source the compressor, heat exchangers, pumps, fans, controls and housing, assemble them, test the unit to your spec and ship it. If something fails, you know who is responsible: us.

The factory can make the part. The question is who answers for the unit.

Chinese factories make good compressors, coils and controllers, and you probably don't doubt that anymore. What goes wrong with a cooling unit happens between the suppliers. The coil maker, the controls vendor, the housing shop and the forwarder each own one part, and nobody owns the unit that fails the leak test.

  1. A batch arrives with a changed tube wall thickness or a different refrigerant fitting, and nobody told you.

  2. You don't know which factory actually built the sub-assembly, or whether it was a trading company all along.

  3. The price moves after the PO, and the blame moves between suppliers.

Every part of a cooling unit, sourced and matched

A cooling unit combines thermal, electronic and mechanical parts that come from different kinds of supplier. We source each one against your drawings and check that they fit and work together before final assembly.

  1. 01

    Compressors

    We source compressors to your spec or from your approved vendor list, and we confirm we're dealing with the actual manufacturer.

  2. 02

    Heat exchangers and coils

    Condensers, evaporators and plate exchangers are checked against your material and dimension callouts before they reach the line.

  3. 03

    Pumps, fans and fittings

    Moving parts and refrigerant connections are matched to the rest of the system, so they fit together at assembly without rework.

  4. 04

    Controls and electronics

    Controllers, sensors, PCBs and wiring harnesses are sourced and checked before they're integrated into the unit.

  5. 05

    Housings and frames

    An out-of-tolerance housing means rework at assembly. We make each one by stamping, die casting, aluminium extrusion or injection moulding and check it against your drawing before it reaches the line.

What we make

Built by specialists in China. Shipped to you.

1M+ products shippedIn Asia since 2006Offices in Stockholm, Ningbo and Seattle

From drawing review to delivery, in five steps

  1. 01 Engineering review

    We check your CAD and BOM for manufacturability before any tooling money is spent. A design that looks finished isn't always one a factory can build.

  2. 02 Multi-supplier sourcing

    We find and audit a supplier for every component, looking at staff, machines, process control, worker safety and management structure. You get one consolidated quote.

  3. 03 Tooling and samples

    Moulds, dies and custom parts, then first-article samples for your sign-off. You decide go or no-go before production starts.

  4. 04 Assembly and QC

    We set up the line with in-process inspection at sub-assembly, then run pressure and performance tests against your spec on the finished unit.

  5. 05 Logistics

    Protective packaging for coils and refrigerant lines, customs documents and freight to the US, UK or EU, planned backwards from your date around Chinese New Year and Golden Week.

You'll know who is building your unit

  1. 01

    People on the factory floor

    Our bilingual delivery managers, based in Ningbo, visit the factories in person. They turn your spec into terms a factory owner acts on, and they report what they actually see on the line.

  2. 02

    Recourse you can use

    You contract through our legal entities in Sweden, the US or China, so if something goes wrong you have a Western-registered company to hold to account.

  3. 03

    NDA on every project

    We sign an NDA before we see your drawings, every time.

Where we fit, and where we don't

  1. Moving from a failing supplier

    We qualify the new line while your current supplier keeps shipping, then cut over once first articles pass. And if your current factory can be fixed, we'll tell you that you don't need to switch.

  2. Scaling an existing unit

    We add capacity and suppliers as volume grows, using the same inspection points on every batch.

  3. Splitting China and Vietnam

    Moving complex production takes time, and many Vietnam lines still use Chinese inputs. We plan for tariff changes in both countries, not only in one.

  4. Consolidating suppliers

    We bring many component vendors under one managed supply chain, with one point of contact.

  5. Not a fit

    If you need a single commodity part at the lowest price, going direct will cost you less. We add value when many suppliers have to be coordinated.

Complete units, tested before they ship

148 components, 72 suppliers and 6 countries went into one full assembly line, built from scratch, delivered on time and run through one point of contact. From prototype to 5,000 units shipped: 200+ components across 18 suppliers, with the assembly line, QC and logistics all managed by us.

  1. 01

    Cooling systems for an equipment company

    The client needed finished cooling units, not loose parts. We sourced the thermal, electronic and housing components, managed pressure and performance testing, and provided certification support and logistics.

  2. 02

    Faults fixed at the factory, not at your dock

    A swapped component or a leak costs far less to fix on the line than in your warehouse. We inspect during assembly and pressure-test each unit, so problems are reworked before the batch is packed.

FAQ

Cooling system manufacturing: common questions

Yes. Sourcing Allies builds complete cooling units. We source the thermal, electronic and housing components from vetted suppliers, manage sub-assembly and final assembly, run pressure and performance testing against your spec and ship the finished unit to the US, UK or EU. You deal with one partner and one point of contact, not a separate vendor for each part.

Each unit goes through in-process inspection at sub-assembly, then pressure and performance testing against your specification before it's packed. Our delivery managers in Ningbo check the line in person.

Yes. Our manufacturing network covers China, Vietnam and India. A cooling system can be built in China, in Vietnam or split between the two. The choice depends on the unit, your tariff exposure, your margins and your timeline. Many Vietnam lines still depend on Chinese-made inputs, so we plan for both countries together.

We source compressors to your specification or from your approved vendor list. Before any order, we confirm we're dealing with the actual manufacturer rather than a trading company and check that its compliance certificates are current and verifiable, because many turn out to be expired. The compressor is then matched and tested with the rest of the system.

Yes, that's how we plan a switch. Your current supplier keeps shipping while we qualify the new factory, make tooling and get first articles approved. Cutover happens only after samples pass. If our review shows your current supplier can be fixed, we'll say so, and you may not need to switch.

We are. Sourcing Allies manages the whole unit, from drawing review to delivery, so a failure doesn't fall between suppliers. You contract with our legal entities in Sweden, the US or China, which gives you recourse through a Western-registered company. We also sign an NDA on every project.

It depends on how complex the unit is and how much tooling it needs. Simpler assemblies justify tooling at lower volumes than complex ones. Send us your spec and BOM and we'll work out the right volume with you.

Bill of materials

What goes into a cooling system

Compressors
Heat exchangers
Pumps
Fans
Controllers
Housings
Fittings
Next step

Bring your drawings. We'll tell you straight whether we can help.

It doesn't matter whether you have a full CAD set or a unit already in production with the wrong supplier. In one meeting, we'll review your BOM, point out the risks and tell you whether we're the right partner.

You’ll speak with Eric, Jeff or Bruce.

A drawing, a sketch or a paragraph is enough to start.

Sourcing Alliessales@sourcingallies.comsourcingallies.com